What roof pitch means
Pitch is how steep a roof is. In the US it is written as inches of rise for every 12 inches of run, so a 6/12 roof climbs 6 inches for each foot it travels across. The run is always measured level, never along the roof itself.
Pitch = rise ÷ run × 12
The same steepness can be given as an angle or as a percent. All three describe one slope.
Angle = arctan(rise ÷ run) and Slope % = rise ÷ run × 100
How to measure your roof pitch
- Hold a level flat against the underside of a rafter in the attic, or on top of the shingles.
- Mark 12 inches along the level from the end that touches the roof.
- At that 12 inch mark, measure straight down (or up) to the roof. That number is the rise.
If you measured 6 inches, you have a 6/12 roof. Measuring from the attic is safer than climbing on the roof.
Common roof pitches
| Pitch | Angle | Slope | Multiplier |
|---|---|---|---|
| 1/12 | 4.76° | 8.3% | 1.003 |
| 2/12 | 9.46° | 16.7% | 1.014 |
| 3/12 | 14.04° | 25.0% | 1.031 |
| 4/12 | 18.43° | 33.3% | 1.054 |
| 5/12 | 22.62° | 41.7% | 1.083 |
| 6/12 | 26.57° | 50.0% | 1.118 |
| 7/12 | 30.26° | 58.3% | 1.158 |
| 8/12 | 33.69° | 66.7% | 1.202 |
| 9/12 | 36.87° | 75.0% | 1.250 |
| 10/12 | 39.81° | 83.3% | 1.302 |
| 11/12 | 42.51° | 91.7% | 1.357 |
| 12/12 | 45.00° | 100.0% | 1.414 |
From pitch to roof area
A sloped roof covers more surface than the floor below it. The pitch multiplier tells you how much more.
Multiplier = √(1 + (pitch ÷ 12)²)
Roof area = (length + 2 × overhang) × (width + 2 × overhang) × multiplier
A worked example
A 40 by 30 foot house with a 12 inch overhang covers 42 by 32 feet, or 1,344 square feet. At 6/12 the multiplier is 1.118, so the roof is about 1,503 square feet. Add 10% for waste and you need 1,653 square feet of shingles. Roofing is sold by the square, which is 100 square feet, so that is 16.5 squares or 50 bundles.
Rafter length uses the same multiplier. Half the 30 foot width plus the 1 foot overhang is a 16 foot run, and 16 × 1.118 is 17 feet 10⅝ inches from the ridge to the edge of the eave. For a cutting length that allows for the ridge board, use the rafter length calculator.
Common questions
What is the most common roof pitch?
Most houses in the US fall between 4/12 and 9/12. Lower pitches are common on ranch houses and additions. Steeper ones show up where snow needs to slide off.
What is the lowest pitch for asphalt shingles?
Shingle makers and most building codes set the minimum at 2/12, and roofs between 2/12 and 4/12 usually need extra underlayment. Below 2/12 a roof needs a membrane or another low-slope material. Check your local code and the shingle maker's instructions before you buy.
Can I walk on my roof?
Roofers generally treat anything up to about 6/12 as walkable with care, and anything steeper as needing roof jacks or a harness. Wet, icy or mossy shingles are slippery at any pitch.
Does this work for a hip roof?
Yes, as long as every side has the same pitch. The area comes out the same as a gable roof over the same house. Hip roofs do waste more shingles on the angled cuts, so use 15% instead of 10%.
How we know this calculator is right
Every time the site is rebuilt, this calculator is run against answers worked out separately from its code. It is not published unless all of them match.
- 4/12 is 18.43° with a multiplier of 1.054. 6/12 is 26.57° and 1.118. 12/12 is 45° and 1.414. These are the standard published figures.
- 9/12 has a multiplier of exactly 1.25, because rise 9, run 12 and rafter 15 make a 3-4-5 triangle.
- Rise 3 over run 6, a 6/12 pitch and an angle of 26.57° all give the same answer, whichever way you enter it.
- A 40 by 30 foot house with 12 inch overhangs at 6/12 has 1,503 square feet of roof and needs 50 bundles with 10% waste.
- The roof area is worked out two ways, footprint times multiplier and two roof planes times rafter length, and the two must agree.
- All twelve rows of the pitch table on this page are compared with the formula.
What this proves: the calculator does the arithmetic of the formulas shown, correctly. What it cannot prove: your measurements, or figures such as waste and coverage, which are typical starting values you can change. Go by the product label and your local code.